Хвостат Хвостатыч (hvostat_hvostat) wrote,
Хвостат Хвостатыч
hvostat_hvostat

Juniper SRX-100: What's inside?

Всё время, пока разбирался с этими симпатичными синими коробочками, всегда было интересен ответ на вполне здравый вопрос любого нормального инженера: А ЧТО У НЕГО ВНУТРИ?

А внутри у него неонка MIPS64-процессор Cavium OCTEON Plus CN5020.

DMESG + фотографии:



Copyright (c) 1996-2010, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 10.0R3.8 #0: 2010-04-15 03:13:36 UTC

builder@ormonth.juniper.net:/volume/build/junos/10.0/release/10.0R3.8/obj-octeon/bsd/sys/compile/JSRXNLE
JUNOS 10.0R3.8 #0: 2010-04-15 03:13:36 UTC

builder@ormonth.juniper.net:/volume/build/junos/10.0/release/10.0R3.8/obj-octeon/bsd/sys/compile/JSRXNLE
real memory = 1073741824 (1024MB)
avail memory = 535977984 (511MB)
cpuid: 0, btlb_cpumap:0xffffffff
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
Initializing watchdog interupt

Loading RT Fifo module.....
Loaded RT Fifo module
pmap_helper loaded (interface version 6, syscall 210)
cpu0 on motherboard
: CAVIUM's Octeon CPU Rev. 0.1 with no FPU implemented
L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
L2 Cache: Size 128kb, ? way
obio0 on motherboard
uart0: on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: on obio0
usb0: DWC OTG Controller
Using DMA mode
Init: Port Power? op_state=1
Init: Power Port (0)
usb0: on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2
uhub1: single transaction translator
uhub1: 2 ports with 1 removable, self powered
umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 3
pcib0: on obio0
Disabling Octeon big bar support
PCI Status: PCI 32-bit: 0xc041b
pcib0: Initialized controller
pci0: on pcib0
pci0: at device 2.0 (no driver attached)
pci0: at device 2.1 (no driver attached)
pci0: at device 2.2 (no driver attached)
cpld0 on obio0
gblmem0 on obio0
octpkt0: on obio0
cfi0: on obio0
platform_cookie_read not implemented
Timecounter "mips" frequency 500000000 Hz quality 0
Timecounters tick every 1.000 msec
Loading the NETPFE ethernet module
Loading E1/T1/J1 driver
Loading the DS1/E1 Media Layer; Attaching to media services layer
Loading common multilink module.
Loading the NETPFE PPPoE module
Loading the netpfe services driver
Loading the XDSL Media Layer; Attaching to media services layer
Loading the IPSec driver
Loading the PTM driver

Loading the DIALER driver
Loading Link Services PICs module.
IPsec: Initialized Security Association Processing.
SMP: AP CPU #1 Launched!
da0 at umass-sim0 bus 0 target 0 lun 0
da0: Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
Trying to create bootdev, rootpartition da0s1a
Trying to mount root from ufs:/dev/da0s1a

Фото потрошков:






_
Tags: juniper, srx100
Subscribe

  • Post a new comment

    Error

    Anonymous comments are disabled in this journal

    default userpic

    Your reply will be screened

    Your IP address will be recorded 

  • 5 comments